Please ensure when fixing the control panel to the wall you use the template provided to prevent any damage during installation, failure to do so may invalidate your warranty
Wiring the motor into the control panel
Left Hand motor wiring Black 5 – Blue 6 – Brown 7
Right Hand motor wiring Brown 5 – Blue 6 – Black 7
Please ensure when fixing the control panel to the wall you use the template provided to prevent any damage during installation, failure to do so may invalidate your warranty.
Please ensure you follow each step before moving onto the next step
Wired Safety Edge Set Up
Remove the resistor from terminals 16 & 17
Wire your spiral cable into the control panel Brown 16, Green 17, White 18
Your spiral cables comes pre-wired into the junction box so all you need to do is wire the opposite end into the control panel.
If correctly wired and no fault exists the green LED light will be permanently ON inside the junction box
Please ensure you follow each step before moving onto the next step.
Motor limits and set up
The control panel has to detect the TOP limit before normal operation and each time after mains power is turned off and then on again.
It is important to set the motor limits first using either a test lead or the two buttons inside the control panel and the limit adjustment screws.
Hold - to - run set up mode
Using either a test lead or the P1 (down) & P2 (up) hold - to - run buttons inside the control panel:
1. Run the motor in the down direction until it stops. At this point attach the curtain via the straps provided unless already attached.
2. Fine adjust the bottom limit.
3. Run the motor up to the top leaving only the bottom piece of the door within the tracks.
4. Fine adjust top limit.
Click on the link below for limit setting instructions.
If the door is moving in the wrong direction:
a. STOP the manoeuvre
b. Switch off the control unit
c. Swap BLACK & BROWN motor wires over – terminals 5 & 7
d. Power up the board again – go back to bullet point 1
Please ensure you follow each step before moving onto the next step.
Now exit set up mode:
Press the P1 & P2 buttons together for 3 times on the 3rd press hold until it beeps
and both L1 & L2 lights go out. P1 & P2 buttins are located within thin the panel. For further support, please watch the video by clicking the livk below.
The panel is now in Day to Day running mode.
You will not be able to pair your transmitters if you are still in set up mode.
Programming a transmitter to 2 channel One button to Open & One button to Close
Please note: you have 8 seconds to do this step, if you get a series of beeps you will need to start the transmitter programming again.
1. Press P1 & P2 together & hold for a few seconds until L1 & L2 lights flash rapidly – you will hear a long beep.
2. Release both buttons then a quick press & release P2 & then press & hold P2 (circled) & at the same time press the top button on your transmitter.
3. The long beep will change to a rapid beep – this means the button is now programmed.
4. Release both buttons & test your transmitter.
5. Please repeat this process for all transmitters.
Please ensure you follow each step before moving onto the next step.
Programming a transmitter to 1 channel - Both doors on one transmitter (2 door installation)
Please note: you have 8 seconds to do this step, if you get a series of beeps you will need to start the transmitter programming again.
1. Press P1 & P2 together & hold for a few seconds until L1 & L2 lights flash rapidly – you will hear a long beep.
2. Press & hold the P2 (circled) button & at the same time press the selected button on your transmitter.
3. The long beep will change to a rapid beep – this means the button is programmed.
4. Release both buttons & test your transmitter.
5. The button chosen will operate as open/stop/close/stop.
6. Please repeat this process if multiple doors are to programmed into this transmitter.
Please ensure you follow each step before moving onto the next stage.
Deleting all transmitters from the control panel
1. Press and hold both P1 and P2 buttons simultaneously until both LEDs on the board are flashing then release
2. Press P1 button 5 times in a quick manner and hold on the 5th press until the sound changes from intermittent to solid (after about 10s)
Please ensure you follow each step before moving onto the next page
Safety Edge Exclusion in the last 5cm of travel
If the door reopens having hit the floor the safety edge exclusion should be set to ‘turn off’ the edge 50mm before it hits the floor.
1. Power on & within 30 seconds L1 & L2 lights are on for 5 Seconds & then L1 & L2 lights turn off.
2. Within 5 seconds of step 1 press & hold P1 & P2 once for 1 second – L1 & L2 lights will flash rapidly.
3. Press P2 button 10 times and keep it pressed on the 10th press for 5 seconds – The buzzer emits 3 beeps
4. Open the door completely by means of a memorized transmitter. The buzzer emits a long beep when the upper limit switch is reached.
5. Put under the door, an object not more than 5cm high. A small piece of wood should be sufficient.
6. Close the door (in hold-to-run mode) keeping your finger pressed on the transmitter with no interruption. The door will stop at the obstacle and the control unit will make a long beep.
7. Open the door completely and remove the object.
8. Close the door to verify the correct application of the procedure.
Please ensure you follow each step before moving onto the next page
Trouble shooting guide.
Comments